TSM/TSSM Trouble codes - Harley Davidson Forums: Harley Davidson Motorcycle Forum
Harley-DavidsonForums.com is an independent enthusiast website owned and operated by VerticalScope Inc. Harley-DavidsonForums.com is not sponsored by or in any way affiliated with Harley-Davidson Inc.. The Harley Davidson names and logos are trademarks owned by Harley-Davidson Inc.

Go Back   Harley Davidson Forums: Harley Davidson Motorcycle Forum > Technical > Electrical

» Insurance
» Our Partners
»ATV Reviews
»Motorcycle Games
Closed Thread
 
LinkBack Thread Tools Display Modes
Old 01-29-2010, 01:48 PM   #1 (permalink)
Grandstanding Member
 
Dave63's Avatar
 
Join Date: Jun 2008
Location: PA
Posts: 29,788
TSM/TSSM Trouble codes

Checking for trouble codes.....Turn signal module/Turn signal security module

To diagnose the TSM/TSSM observe the behavior of the turn signals.

1 Set Run switch to Run - -

2 Turn Ignition key On-Off-On-Off-On-Off-On and then toggle the Left Turn Signal switch twice. - -

3 Turn Ignition key Off-On Verify the Check Engine lamp and Security Lamp illuminate briefly and then turn off. Security lamp will not illuminate on non-security (TSM) Twin Cam models.

4 Attempt normal start one time. Engine starts and stalls immediately. check engine lamp stays on. Password has not been learned and sets trouble code P1009, thus stopping fuel flow.

5 Wait 10 seconds Security Lamp remains lit for V-Rod and TC88 with TSSM. Lamp will not be on for TC88 TSM models. ECM enters Password Learning mode for 10 minutes. Do Not cycle the ignition or disrupt power.

6 Wait until Security Lamp turns off or a minimum of 10 minutes has passed. - -

7 Quickly (within 2 seconds) turn Ignition key OFF-ON Security Lamp remains lit for V-Rod and TC88 with TSSM. Lamp will not be on for TC88 TSM models. -

8 Wait until Security Lamp turns off or a minimum of 10 minutes has passed. - Password Learning mode for 10 minutes. Do Not cycle the ignition or disrupt power.

9 Quickly (within 2 seconds) turn Ignition key OFF-ON Security Lamp remains lit for V-Rod and TC88 with TSSM. Lamp will not be on for TC88 TSM models. -

10 Wait until Security Lamp turns off or a minimum of 10 minutes has passed. - Password Learning mode for 10 minutes. Do Not cycle the ignition or disrupt power.

11 Quickly (within 2 seconds) turn Ignition key OFF-ON Security Lamp light and then turn off. Lamp will not be on for TC88 TSM models. -

12 Turn Ignition switch OFF. Wait 15 seconds. Turn Ignition switch ON and start engine to confirm the Password Learn Procedure is successful. Engine will start and remain running. If engine immediately stalls and fails to restart the procedure was not successful. Start over at step 1. -

The above steps must be timed and performed exactly as described. Any deviation will require you to start again from step 1.


If the signals flash six fast 4-way flashes shortly after key on,
then an error code has been logged.

Code Types
There are two types of trouble codes:
Current and Historic.
If a trouble code is stored, it can be read using TSM/TSSM Diagnostics.

Current
Current trouble codes are those which are present during the current ignition cycle.

Historic
If a particular problem happens to resolve itself, the active status
problem is dropped and it becomes a historic code rather than a current code.
Intermittent output shorts can become typical historic codes.
Historic codes are stored for 50 ignition cycles.
It is important to note that historic codes will exist whenever the system
indicates the existence of a current fault.

Notes
*If the turn signals flash six four way flashes shortly after key on, it indicates an error code has been logged sometime in the last 3 ignition cycles. On vehicles with TSSM, the security lamp will also light for eight seconds after the bulb check if historic codes are present.

*The security lamp will stay on if current code(s) are set. If a historic code is present, the security lamp will light for 50 ignition cycles or until the code is cleared manually.

Invoking TSM/TSSM diagnostics

1: Set Run/Stop switch to off

2: Turn ign key ON-OFF-ON-OFF-ON

3: Press the left turn switch two times and release.
*The signals flash 2 times for a Domestic TSSM

4: Press the right turn switch 1 time and release.
*The signals flash 1 time.

5: Press the right turn switch 1 time and release.
*The signals flash 2 times.

6: Press the right turn switch 1 time and release.
*The signals flash 3 times.

7: Press the left turn switch 1 time and release.
*The signals flash out the trouble codes.
There is a 1.5 sec pause between flashes to distinguish between 1st and 2nd digit of codes.
There is a 4 second pause between codes, then it will loop and repeat codes.
If the light comes on for 4 seconds after invoking test then goes out for good,
there are no codes stored.....test over....turn ignition off.
Wait at least 10 seconds
before turning ignition on again.

8: To clear codes (after repairs) press and hold left turn switch for 4-5 seconds at end of test.
* The signals flash 2 times to confirm your request.
Codes
11= Battery voltage high
21= left turn output fault
22= Right turn output fault
25= Ignition enable output high
31= alarm output low
32= alarm output high
34= starter output high
35= accelerometer fault
41= Ignition switch open/low

Possible causes
11= battery voltage >16.0v/battery charger used/voltage regulator Bad. (pin 1 / Bn/Gy)

21= bulbs/shorts/bad connections if no voltage on pins 5 or 6 with 4ways on TSSM Bad

25= should be no voltage present on pin 10 with key off. (Lt Grn/Gy wire on TSSM)

31&32= Middle pin on siren goes low voltage to fire alarm, high voltage to stop.
If the siren responds with 3 chirps instead of 2 the siren battery is bad.
Pin A (Bn/Gy) is positive voltage downstream of the 15amp security fuse.
Pin C (Bk) is ground from pin 12 (Bk) on TSSM

34= Starter relay and coil are grounded via TSSM when disarmed and ignition on.
This code means the ground is from someplace else...short/hot wired..etc.
Starter relay could be bad (voltage present on pin 9)(Tn/Gn) when not starting engine.

35= TSM/TSSM bad. bank angle and tamper will not function when this code is set.

41= Signals will not flash due to shorts, bad connections/wiring/bulbs/TSSM Bad

More notes

*If the siren Chirps 3 times instead of 2 this means time for a new siren battery.

*There can be codes set in the TSSM without any visual indications ie: Security lamp/ Signals

*There needs to be 12.0vdc available from the main battery

*There are 4 sensitivity settings for alarm activation, with regard to motion.

*There is an Auto Arming feature available, all domestics are shipped with this disabled.

*Always disarm the TSSM before disconnecting the battery, or siren will activate.(If present)
If auto arming is activated, you have 30 seconds after disarming to pull the fuse to accomplish the above.

*Tampering or problems with the security light circuit activates the alarm for 30 seconds.

*Storage mode time is selectable, and will shut down system at 30,60,or 90 days, or never.
Key fob will not work after shut down. Turn ignition ON to re-activate, the alarm will sound
if it was armed prior to storage mode shut down. Use the key fob to disable the alarm.

*IF you render the key fob useless and did not program a personal override code in the TSSM,
you are not only buying a new fob, you are buying a new TSSM as well.
Once it learns a key fob, it learns no more.

TSM/TSSM Pinouts

1= Battery (Bn/Gy)
2= Ignition (Gy)
3= VSS/Serial Data link
4= Security indicator (Bn/V)
5= Left turn Feed (V)
6= Right turn Feed (Bn)
7= Right turn switch input (W/Bn)
8= Left turn switch input (W/V)
9= Start relay Control (Tn/Gn)
10= Ignition enable signal (LGn/Gy)
11= Alarm signal (Lgn/Bn)
12= Ground (Bk)
__________________
__________________________________________
“When the going gets weird, the weird turn professional....” ~ Hunter S. Thompson~

R.I.P. Rubberdown. 1971-2012

Last edited by Dave63; 01-29-2010 at 08:11 PM.
Dave63 is online now  
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Powered by vBadvanced CMPS v3.2.2

All times are GMT -5. The time now is 12:29 PM.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
This site is in no way affiliated with Harley-Davidson
Motorcycle News, Videos and Reviews
Honda Grom Forum Harley Davidson Forum Honda 600RR Kawasaki Forum Yamaha R6 Forum Yamaha FZ-09 Forum
1199 Panigale Forum Roadglide Forum Honda CBR1000 Forum Vulcan Forum Yamaha R1 Forum Yamaha R3 Forum
Ducati Monster Forum Harley Forums Honda CBR250R Forum ZX10R Forum Star Raider Forum Yamaha Viking Forum
Suzuki GSXR Forum V-Rod Forums Honda Shadow Forum Kawasaki Motorcycle Forum Star Warrior Forum KTM Duke 390 Forum
SV650 Forum BMW S1000RR Forum Honda Fury Forum Kawasaki Versys Forum Drag Racing Forum Ducati 899 Panigale Forum
Suzuki V-Strom BMW K1600 Triumph Forum Victory Forums Sportbikes BMW NineT Forum
Volusia Forum BMW F800 Forum Triumph 675 Forum MV Agusta Forum HD Street Forum Suzuki GW250 Forum
Yamaha Motorcycles Victory Gunner Forum Honda Vultus Forum HD LiveWire Forum Ninja H2 Forum